[2024] Use Valid New NSE7_NST-7.2 Questions – Top choice Help You Gain Success [Q21-Q37]

Rate this post

[2024] Use Valid New NSE7_NST-7.2 Questions – Top choice Help You Gain Success

NSE7_NST-7.2 Exam Practice Materials Collection

QUESTION 21
Refer to the exhibit. whichcontains the output of diagnose vpn tunnellist.

Which command will capture ESP traffic for the VPN named DialUp_0?

diagnose sniffer packet any ‘host10.0.10.10’

diagnose sniffer packet any ‘ip proto 50’

diagnose sniffer packet any ‘esp and host 10*200.3.2’

diagnose sniffer packet any ‘port 4500’

QUESTION 22

If the default settings are in place, what can you conclude about the conserve mode shown in the exhibit?

FortiGate is currently blocking new sessions that require flow-based or proxy-based content inspection.

FortiGate is currently blocking all new sessions regardless of the content inspection requirements or configuration settings because of high memory use.

FortiGate is currently allowing new sessions that require flow-based or proxy-based content inspection but is not performing inspection on those sessions.

FortiGate is currently allowing new sessions that require flow-based content inspection and blocking sessions that require proxy-based content inspection.

QUESTION 23
What are two functions of automation stitches? (Choose two.)

You can configure automation stitches on any FortiGate device in a Security Fabric environment.

You can create automation stitches to run diagnostic commands and attach the results to an email message when CPU or memory usage exceeds specified thresholds.

An automation stitch configured to execute actions sequentially can take parameters from previous actions as input for the current action.

You can set an automation stitch configured to execute actions in parallel to insert a specific delay between actions.

QUESTION 24
Which three conditions are required for two FortiGate devices to form an OSPF adjacency? (Choose three.)

OSPF link costs match.

OSPF interface priority settings are unique

OSPF interface network types match

Authentication settings match.

OSPF router IDs are unique.

QUESTION 25

Refer to the exhibit, which shows the output of a diagnose command.
What can you conclude from the RTT value?

Its value represents the time it takes to receive a response after a rating request is sent to a particular server.

Its value is incremented with each packet lost.

It determines which FortiGuard server is used for license validation.

lts initial value is statically set to 10.

QUESTION 26
Consider the scenario where the server name indication (SNI) does not match either the common name (CN) or any of the subject alternative names (SAN) in the server certificate. Which action will FortiGate take when using the default settingsfor SSL certificate inspection?

FortiGate closes the connection because this represents an invalid SSL/TLS configuration

FortiGate uses the 31 information from the Subject field in the server certificate.

FortiGate uses the first entry listed in the SAN field in the server certificate.

FortiGate uses the SNI from the user’s web browser.

QUESTION 27

Refer to the exhibits, which show the configuration on FortiGate and partial session information for internet traffic from a user on the internal network.
If the priority on route ID _ were changed from 10 to 0, what would happen to traffic matching that user session?

The session would be deleted, and the client would need to start a new session.

The session would remain in the session table, but its trafficwould now egress from both port1.andport2.

The session would remain in the session table, and its traffic would egress from port2.

The session would remain in the session table, and itstraffic would egress from port1.

QUESTION 28
Refer to the exhibit, which shows a truncated output of a real-time LDAP debug.

What two conclusions can you draw from the output? (Choose two.)

The name of the configured LDAP server is Lab.

The user is authenticating using CN=John Smith.

FortiOS is able to locate the user in step 3 (Bind Request) of the LDAP authentication process.

FortiOS is performing the second step (Search Request) in the LDAP authentication process.

QUESTION 29
Exhibit.

Refer to the exhibit, which shows partial outputs from two routing debug commands.
Why is the port 2 default route not in the second command output?

The port2 interlace is disabled in the FortiGate configuration.

The port1 default route has a higher priority value than the default route using port2.

The port1default route has a lower priority value than the default route using port2.

The port1 default route has a lower distance than the default route using port2-

QUESTION 30
Exhibit.

Refer to the exhibit, which shows the omitted output of diagnose npu np6 port-list on a FortiGate1500D.
An administrator is unable to analyze traffic flowing between port1 and port7 using the diagnose sniffer command.
Which two commands allow the administrator to view the traffic? (Choose two.)

QUESTION 31
Which three common FortiGate-to-collector-agent connectivity issues can you identifyusing the FSSO real-time debug?(Choose three.)

Refused connection. Potential mismatch of TCP port.

Mismatched pre-shared password.

Inability to reach IP address of the collector agent.

Log is full on the collector agent.

Incompatible collector agent software version.

QUESTION 32
Refer to the exhibit, which shows two entries that were generated in the FSSO collector agent logs.

What three conclusions can you draw from these log entries? (Choose three.)

Remote registry is not running on the workstation.

The FortiGate firmware version is not compatible with that of the collector agent

DNS resolution is unable to resolve the workstation name.

The user’s status shows as “not verified” in the collector agent

A firewall is blocking traffic to port 139 and 445.

QUESTION 33
Exhibit.

Refer to the exhibit, which contains partial output from an IKE real-time debug.
The administrator does not have access to the remote gateway.
Based on the debug output, which configuration change can the administrator make to the local gateway to resolve the phase 1 negotiation error?

In the phase 1 proposal configuration, add AESCBC-SHA2 to the list of encryption algorithms.

In the phase 1 proposal configuration, add AES256-SHA256 to the list of encryption algorithms.

In the phase 1 proposal configuration, add AES128-SHA128 to the list of encryption algorithms.

In the phase 1 network configuration, set the IKE version to 2.

QUESTION 34
Refer to the exhibit.

FortiGate has already been configured with a firewall policy that allows all ICMP traffic to flow from port1 to port3.
Which changes must the administrator perform to ensure the server at 10.4.0.1/24 receives the echo reply from the laptop at 10.1.0.1/24?

Enable asymmetric routing under config system settings.

Modify the default gateway on thelaptop from 10.1.0.2 to 10.2.0.2

A firewall policy that allows all ICMP traffic from port3 to port1.

Change the configuration from strict RPF check mode to feasible RPF check mode

QUESTION 35
Which two statements about application-layer test commands ate true? (Choose two.)

Some of them display statistics and configuration information about a feature or process.

Some of them display real-time application debugs.

Some of them display only output, after you run the diagnose debug console enable command.

Some of them can be used to restart an application.

QUESTION 36
Refer to the exhibit, which shows the output of diagnose syssessionstat. Which statement about the output shown in the exhibit is correct?

AII the sessions in the session table are TCP sessions.

162 sessions have been deleted because of memory page exhaustion.

There are 166 TCP sessions waiting to complete the three-way handshake.

There are two sessions that have not been removed in case of any out-of-order packets that arrive.

Fortinet NSE7_NST-7.2 Exam Syllabus Topics:

Topic	Details
Topic 1	System troubleshooting: It discusses troubleshooting of automation stitches, resource problems, different operation modes, security fabric issues, and connectivity problems.
Topic 2	Security profiles: The topic delves into the sub-topics related to troubleshooting of FortiGuard issues, web filtering issues, and the intrusion prevention system (IPS).
Topic 3	Routing: This topic discusses troubleshooting of routing packets, BGP routing, and OSPF routing.
Topic 4	VPN: Troubleshooting of IPsec IKE version 1 and 2 issues is discussed in this topic.
Topic 5	Authentication: This topic focuses on troubleshooting of local and remote authentication and Fortinet Single Sign-On (FSSO) issues.