Updated Mar-2025 100% Cover Real FCP_FAZ_AD-7.4 Exam Questions – 100% Pass Guarantee [Q17-Q33]

Rate this post

Updated Mar-2025 100% Cover Real FCP_FAZ_AD-7.4 Exam Questions – 100% Pass Guarantee

Use Real Fortinet Dumps – 100% Free FCP_FAZ_AD-7.4 Exam Dumps

QUESTION 17
Which two settings must you configure on FortiAnalyzer to allow non-local administrators to authenticate on FortiAnalyzer with any user account in a single LDAP group? (Choose two.)

A local wildcard administrator account

An administrator group

One or more remote LDAP servers

LDAP servers IP addresses added as trusted hosts

A wildcard administrator account allows any user from the specified LDAP group to authenticate, and the remote LDAP servers must be configured to validate those user credentials. The combination of these settings enables authentication via LDAP for non-local users.

QUESTION 18
Which two statements are true regarding log fetching on FortiAnalyzer? (Choose two.)

A FortiAnalyzer device can perform either the fetch server or client role, and it can perform two roles at the same time with the same FortiAnalyzer devices at the other end.

Log fetching can be done only on two FortiAnalyzer devices that are running the same firmware version.

Log fetching allows the administrator to fetch analytics logs from another FortiAnalyzer for redundancy.

Log fetching allows the administrator to run queries and reports against historical data by retrieving archived logs from one FortiAnalyzer device and sending them to another FortiAnalyzer device.

Reference:
Using FortiAnalyzer, you can enable log fetching. This allows FortiAnalyzer to fetch the archived logs of specified devices from another FortiAnalyzer, which you can then run queries or reports on for forensic analysis.
The FortiAnalyzer device that fetches logs operates as the fetch client, and the other FortiAnalyzer device that sends logs operates as the fetch server. Log fetching can happen only between two FortiAnalyzer devices, and both of them must be running the same firmware version. A FortiAnalyzer device can perform either the fetch server or client role, and it can perform two roles at the same time with different FortiAnalyzer devices at the other end.
FortiAnalyzer_7.0_Study_Guide-Online pag. 168

QUESTION 19
Which statements are true regarding securing communications between FortiAnalyzer and FortiGate with IPsec? (Choose two.)

Must configure the FortiAnalyzer end of the tunnel only–the FortiGate end is auto-negotiated.

Must establish an IPsec tunnel ID and pre-shared key.

IPsec cannot be enabled if SSL is enabled as well.

IPsec is only enabled through the CLI on FortiAnalyzer.

Option B is correct because you must establish an IPsec tunnel ID and pre-shared key to secure the communication between FortiAnalyzer and FortiGate with IPsec12. The tunnel ID is a unique identifier for each tunnel and the pre-shared key is a secret passphrase that authenticates the peers.
Option D is correct because IPsec is only enabled through the CLI on FortiAnalyzer1. You cannot configure IPsec settings through the GUI on FortiAnalyzer.

QUESTION 20
Which daemon is responsible for enforcing the log file size?

sqlplugind

logfiled

miglogd

ofrpd

FortiAnalyzer_7.0_Study_Guide-Online.pdf page 121: The logfiled process enforces the log file size and is also responsible for disk quota enforcement by monitoring the other processes.

QUESTION 21
Which two statements about FortiAnalyzer operating modes are true? (Choose two.)

When in collector mode, FortiAnalyzer offloads the log receiving task to the analyzer.

When in analyzer mode, FortiAnalyzer supports event management and reporting features.

For the collector, you should allocate most of the disk space to analytics logs.

Analyzer mode is the default operating mode.

When in analyzer mode, FortiAnalyzer supports event management and reporting features.
In analyzer mode, FortiAnalyzer provides full support for log analysis, event management, and reporting capabilities.
Analyzer mode is the default operating mode.
By default, FortiAnalyzer operates in analyzer mode, which allows for log analysis and reporting.
The other options are incorrect because:
In collector mode, the FortiAnalyzer primarily stores logs and forwards them to another FortiAnalyzer in analyzer mode, not the other way around.
In collector mode, most disk space is usually allocated to storage rather than analytics, as the logs are primarily stored for forwarding.

QUESTION 22
If the primary FortiAnalyzer in an HA cluster fails, how is the new primary elected?

The configured IP address is checked first.

The active port number is checked first.

The firmware version is checked first.

The configured priority is checked first

In the case of a primary device failure, FortiAnalyzer HA uses the following rules to select a new primary:
* All cluster devices are assigned a priority from 80 to 120. The default priority is 100. If the primary device becomes unavailable, the device with the highest priority is selected as the new primary device. For example, a device with a priority of 110 is selected over a device with a priority of 100.
* If multiple devices have the same priority, the device whose primary IP address has the greatest value is selected as the new primary device. For example, 123.45.67.124 is selected over 123.45.67.123.
* If a new device with a higher priority or a greater value IP address joins the cluster, the new device does not replace (or pre-empt) the current primary device automatically.
FortiAnalyzer_7.0_Study_Guide-Online page 62

QUESTION 23
An administrator, fortinet, can view logs and perform device management tasks, such as adding and removing registered devices. However, administrator fortinet is not able to create a mail server that can be used to send alert emails.
What can be the problem?

ADOM mode is configured with Advanced mode.

A trusted host is configured.

fortinet is assigned the default Standard_User administrative profile.

fortinet is assigned the default Restricted_User administrative profile.

The Standard_User profile allows viewing logs and performing some device management tasks but typically does not allow configuring global settings like creating a mail server for alert emails. To create a mail server, the administrator would need to have a profile with higher privileges, such as Super_User or a custom profile with the necessary permissions.

QUESTION 24
Which statement describes online logs on FortiAnalyzer?

Logs that reached a specific size and were rolled over

Logs that can be used to create reports

Logs that can be viewed using Log Browse

Logs that are saved to disk, compressed, and available in FortiView

QUESTION 25
By default, what happens when a log file reaches its maximum file size?

FortiAnalyzer overwrites the log files.

FortiAnalyzer stops logging.

FortiAnalyzer rolls the active log by renaming the file.

FortiAnalyzer forwards logs to syslog.

QUESTION 26
What purposes does the auto-cache setting on reports serve? (Choose two.)

To reduce report generation time

To automatically update the hcache when new logs arrive

To reduce the log insert lag rate

To provide diagnostics on report generation time

QUESTION 27
Refer to the exhibit.

Which image corresponds to the packet capture shown in the exhibit?

The exhibit shows a packet capture with a syslog message containing a log event from a FortiGate device. This log event includes several details such as the date, time, and event message. The corresponding image that matches this packet capture would be the one which shows that the FortiGate device has logs being received in real-time, as indicated by the highlighted section in the packet capture where it mentions “real-time”. Therefore, Option A is the correct answer because it shows logs with “Real Time” status for the FortiGate-VM64 device, indicating that this FortiAnalyzer is currently receiving real- time logs from the device, matching the activity in the packet capture.
Reference: Based on the provided exhibits and the real-time logging information, correlated with the knowledge from the FortiAnalyzer 7.2 Administrator documentation regarding log reception and device management.

QUESTION 28
On the RAID management page, the disk status is listed as Initializing.
What does the status Initializing indicate about what the FortiAnalyzer is currently doing?

FortiAnalyzer is ensuring that the parity data of a redundant drive is valid

FortiAnalyzer is writing data to a newly added hard drive to restore it to an optimal state

FortiAnalyzer is writing to all of its hard drives to make the array fault tolerant

FortiAnalyzer is functioning normally

Reference:
8977-00505692583a/FortiAnalyzer-5.6.10-Administration-Guide.pdf (40)

QUESTION 29
Refer to the exhibit.

Which image corresponds to the packet capture shown in the exhibit?

QUESTION 30
What is the recommended method of expanding disk space on a FortiAnalyzer VM?

From the VM host manager, add an additional virtual disk and use the #execute lvm extend <disk number> command to expand the storage

From the VM host manager, expand the size of the existing virtual disk

From the VM host manager, expand the size of the existing virtual disk and use the # execute format disk command to reformat the disk

From the VM host manager, add an additional virtual disk and rebuild your RAID array

https://kb.fortinet.com/kb/documentLink.do?externalID=FD40848

QUESTION 31
Which two constraints can impact the amount of reserved disk space required by FortiAnalyzer? (Choose two.)

License type

Disk size

Total quota

RAID level

https://docs.fortinet.com/document/fortianalyzer/6.2.5/administration-guide/368682/disk-space-allocation

QUESTION 32
Which feature can you configure to add redundancy to FortiAnalyzer?

Primary and secondary DNS

VLAN interfaces

IPv6 administrative access

Link aggregation

Link aggregation is a method used to combine multiple network connections in parallel to increase throughput and provide redundancy in case one of the links fail. This feature is used in network appliances, including FortiAnalyzer, to add redundancy to the network connections, ensuring that there is a backup path for traffic if the primary path becomes unavailable.
Reference: The FortiAnalyzer 7.4.1 Administration Guide explains the concept of link aggregation and its relevance to

QUESTION 33
Which statement about the communication between FortiGate high availability (HA) clusters and FortiAnalyzer is true?

If devices were registered to FortiAnalyzer before forming a cluster, you can manually add them together.

FortiAnalyzer distinguishes each cluster member by the IP addresses in log message headers.

If the HA primary device becomes unavailable, you must remove it from the HA cluster list on FortiAnalyzer.

The FortiGate HA cluster must be in active-passive mode in order to avoid conflict.

This allows FortiAnalyzer to correctly identify and process logs from different members of the HA cluster.

Loading …

Fortinet FCP_FAZ_AD-7.4 Exam Syllabus Topics:

Topic	Details
Topic 1	Logs and Reports Management: This part of the exam measures the candidate’s ability to handle log data and generate reports using FortiAnalyzer. Network and security analysts must show proficiency in managing, analyzing, and reviewing logs to ensure effective system monitoring and auditing processes are in place.
Topic 2	Device Management: Here, Fortinet network and security analysts are evaluated on their ability to handle devices linked to FortiAnalyzer. This includes adding new devices, managing them efficiently, and troubleshooting communication issues.
Topic 3	Administration: This section evaluates the ability of network and security analysts to configure administrative access and manage Administrative Domains (ADOMs). It covers tasks such as setting user permissions, managing backups, and disk quotas, and ensuring secure and efficient management of administrative privileges within FortiAnalyzer systems.
Topic 4	System Configuration: This section assesses the capabilities of network and security analysts in managing FortiAnalyzer systems. It includes tasks like performing initial configurations, setting up high-availability systems, and configuring RAID for storage.