QUESTION 12
Your customer has an HPE Synergy platform deployed and managed using HPE OneView. The customer also has HPE Superdome Flex with RMC deployed They plan to deploy a second nPar and HPE Superdome Flex
280 They plan to manage new components using HPE OneView
What must be done to achieve this goal?

QUESTION 13
In the past a customer experienced a networking issue where network ports went down and came back up in quick succession.
Which HPE Virtual Connect SE 100 GD F32 Module for HPE Synergy feature can be configured to disable such ports?

QUESTION 14
An HPE Synergy customer needs to prevent a timeout and loss of communication during an external switch firmware upgrade.
Click the parameter that the customer should configure within an uplink set to meet this requirement

QUESTION 15
You plan to configure a Link Aggregation Group (LAG) for two connections within a server profile for a compute node running an ESXI system.
What is required from the VMware side to enable LAG?

QUESTION 16
Your customer experienced some problems caused by outdated HPE Superdome Flex firmware. Which update method should they use to avoid these issues in the future?

QUESTION 17
Which statement about a new HPE SimpliVity deployment is true?

QUESTION 18
Your customer wants to compare HPE Superdome Flex with HPE Superdome Flex 280.
Which statement about these two systems is true?

QUESTION 19
Click the area within the iLO management interface that will allow you to access workload Advisor.

QUESTION 20
Which statement about HPE OneView milestone releases is true?

QUESTION 21
Your customer plans to deploy VMware ESXi 7 0 U2 and they are looking for a hardware platform mat wilt allow them to use up to 24 TB of physical memory.
Which HPE compute system meets this customer’s requirements?

QUESTION 22
Your customer wants to add a second HPE Synergy frame to an existing logical enclosure Based on a single HPE Synergy frame. The customer wants to use a highly available master setup.
Which procedures should De performed during the expansion process? (Select two.)

QUESTION 23
Your customer needs to move an application from an HPE Synergy 480 Gen10 Compute Module to an HPE Synergy 660 Gen 10 Compute Module. The 480 has a switch that has been manually zoned outside of HPE OneView.
What must the customer do before migrating the application?

QUESTION 24
Your customer plans to deploy a VMware ESXi with HPE Synergy platform. They plan to use Distributed Switches and DRS cluster You are preparing a proposal with the following components:
– HPE Synergy frame with ten HPE Synergy 480 Gen10 Plus compute modules
– two HPE Virtual Connect SE 100Gb F32 Modules for Synergy
– an appropriate number of the vSphere Standard licenses for each compute node
– one HPE D3940 Storage Modules with 40 SSDs – all required cables and options Which statement about this proposal is true?

QUESTION 25
Refer to the exhibit.

Which statement about this logical JBOD is true?

QUESTION 26
After HPE Superdome Flex deployment and nPar setup, you need to verify health status of HPE Superdome Flex components.
Put the steps on the left into the coned order on the right to perform this task.

QUESTION 27
Match HPE SimpliVity term with the definition.

QUESTION 28
Your customer plans to manage HPE Primera using HPE Oneview
Which storage management tasks can be completed using HPE OneView for this environment?

QUESTION 29
Which compute node parameters are captured within server hardware type?

QUESTION 30
Your customer reports mat an external FC boot volume for Windows server is visible four times in the Disk Management 1 online and 3 offline.
What should you do to resolve this issue?

QUESTION 31
Your customer has a logical enclosure configured using a angle HPE Synergy frame with the following configuration
– two HPE Virtual Connect SE 100Gb F32 Modules for Synergy
– two HPE Synergy Virtual Connect SE 32Gb FC Modules -12 HPE Synergy 480 Gen10 Plus compute nodes with appropriate mezzanine cards They plan to add a new HPE Synergy frame to an existing logical enclosure with the following configuration
– two HPE Synergy Virtual Connect SE 32Gb FC Modules
– two HPE Synergy 20Gb interconnect Link Modules
– Eight HPE Synergy 480 Gen 10 Plus compute nodes with appropriate mezzanine cards Which statement about the planned configuration change is true?