Get Ready with JN0-363 Exam Dumps (2025) [Q45-Q69]

Rate this post

Get Ready with JN0-363 Exam Dumps (2025)

Realistic JN0-363 Dumps are Available for Instant Access

If you are looking to become an expert in service provider routing and switching, the Juniper JN0-363 exam is an excellent choice. It covers a wide range of topics and requires a deep understanding of networking fundamentals and Juniper Networks technologies. With the right preparation and dedication, passing JN0-363 exam can help you advance your career and demonstrate your expertise to potential employers.

The JN0-363 exam is intended for network professionals who are responsible for managing and maintaining service provider networks. This includes network administrators, network engineers, and network architects. Candidates for the JN0-363 exam should have a solid understanding of networking fundamentals, as well as experience working with Juniper Networks routing and switching devices. The JN0-363 exam provides a valuable certification for individuals seeking to advance their careers in the field of service provider routing and switching.

NEW QUESTION 45
Which two statements are correct about the service provider MPLS network shown in the exhibit? (Choose two.)

R3 will perform a label pop operation on the transport MPLS label.

Traffic from Network 1 to Network 3 and traffic from Network 1 to Network 4 each need their own unique label-switched path.

Traffic from Network 1 to Network 3 and from Network 1 to Network 4 can share the same label- switched path.

R3 will perform a label swap operation on the transport MPLS label.

NEW QUESTION 46
Exhibit

You configured interface ge-0/070.0 to run IS-IS. but this interface does not appear in the output of the show isis adjacency command as shown in the exhibit.
What is the problem in this scenario?

This is a Gigabit Ethernet interface, that is incompatible with the reference-bandwidth 100g statement.

The family iso statement must be added to the logical interface.

The router at the other end of the link Is not sending any IS-IS Hello messages.

The router at the other end of the link is a Level 1 only router.

NEW QUESTION 47
Click the Exhibit.

Referring to the exhibit, what is the correct OSPF interface state for the ge-0/0/1 interface?

BDR

Down

DRother

NEW QUESTION 48
Click the Exhibit button.

Referring to the exhibit, which statement is correct?

Routes from 10.1.1.1 are more preferred than routes from 10.2.2.2

Routes from 10.2.2.2 are less preferred than the default local preference

Routes from 10.3.3.3 are more preferred than the default local preference

Routes from 10.2.2.2 are less preferred than routes from 10.3.3.3

NEW QUESTION 49
Which two statements are true when configuring OSPF authentication? (Choose two.)

An OSPF link can support both simple password and MD5 authentication at the same time.

An MD5 password requires a key ID.

You can configure multiple MD5 passwords simultaneously on the same link.

If the MD5 password negotiation fails, you can configure OSPF to automatically use a simple password as a backup.

NEW QUESTION 50
Which two statements are correct when using LDP? (Choose two.)

The lnet.3 table will contain only the paths explicitly defined.

The inet.3 table will contain a full mesh of label-switched paths to other LDP-enabled routers.

LDP label-switched paths are created by configuring LDP on at least one physical router interface.

LDP label-switched paths are created by configuring LDP on the loopbacK Interface.

NEW QUESTION 51
Which LSA type does an OSPF ABR use to advertise external routes generated by an NSSAASBR into the backbone?

Type 5

Type 7

Type 3

Type 1

NEW QUESTION 52
Click the Exhibit button.

You are configuring an IBGP group. When you commit your configuration, you receive the error shown in the exhibit.
Which additional configuration parameter must you add to your configuration?

multipath

type external

type internal

export <policy name>

NEW QUESTION 53
Referring to the exhibit, how do you verify the status of the tunnel from R1?

Issue the ping 172.20.111.10 source 172.20.110.1 command.

Issue the ping 172.20.111.10 source 198.51.100.1 command.

Issue the ping 172.20.111.10 source 203.0.113.2 command.

Issue the ping 172.20.111.10 command.

NEW QUESTION 54
Exhibit

Referring to the exhibit, what must be included in the Route1 configuration when establishing an EBGP session with the ISP?

A local address must be specified.

A local AS must be specified.

The BGP session type internal must be specified.

The BGP session type external must be specified.

NEW QUESTION 55
You are asked to configure filter-based forwarding on a Junos device.
Which two statements are correct in this scenario? (Choose two.)

You must create a routing policy.

You must create a route target.

You must create and apply a match filter.

You must create a routing instance.

NEW QUESTION 56
Which two statements are correct about IS-IS? (Choose two.)

A level 1 only router can never form an adjacency with a level 2 only router.

For level 2 adjacencies, the area IDs can be different.

For level 2 adjacencies, the area IDs must be the same.

A level 1 only router can form an adjacency with a level 2 only router.

NEW QUESTION 57
Click the Exhibit button. You have two routers connected over a Gigabit Ethernet link as shown in the exhibit It is required that an IS-IS adjacency be established without the need for a designated intermediate system (DIS)

Which configuration statement entered on both routers will achieve this goal?

set interface ge-0/0/2 unit 0 family iso no-dis

set interface ge-0/0/2 unit 0 family iso point-to-point

set protocols isis interface ge-0/0/2.0 no-dis

set protocols isis interface ge-0/0/2.0 point-to-point

NEW QUESTION 58
You confirm that the R2 and R3 routers are receiving a BGP route to the 203.0.113.0/24 network, but both routers display the route as hidden. Referring to the exhibit, which two actions solve this problem? (Choose two.)

Apply the routing policy on R1 as an export policy to the IBGP group.

Apply the touting policy on R1 as an import policy to the IBGP group.

Configure a routing policy on R1 that sets the next hop for the 203.0.113.0/24 BGP route to the IP address that R1 uses for IBGP peering.

Configure a routing policy on R1 that sets the next hop for the 203.0.113.0/24 BGP route to the IP address that R1 uses for EBGP peering.

NEW QUESTION 59
Which two statements are true about IBGP on MX Series devices? (Choose two.)

Neighbors can be located anywhere within the AS

Interface Lo0 must be used for peering

It does not support multihop

It is loop free by default

NEW QUESTION 60
The segment touting SRGB start label Is 10,000 and the SRGB index range is 500.
In this scenario, which two statements are correct? (Choose two.)

The first usable label is 10,001.

The last usable label is 10.501.

The last usable label is 10,499.

The first usable label Is 10,000.

NEW QUESTION 61
Router A receives two similar route advertisements from different BGP peers.What would cause a route to be selected in this scenario?

having a lower MED value

having a lower local preference

learning a route from a peer with a higher peer ID

learning a route from a peer with a higher IGP metric

NEW QUESTION 62
Click the Exhibit button.

Referring to the exhibit, which statement is correct?

Routes from 10.1.1.1 are more preferred than routes from 10.2.2.2

Routes from 10.2.2.2 are less preferred than the default local preference

Routes from 10.3.3.3 are more preferred than the default local preference

Routes from 10.2.2.2 are less preferred than routes from 10.3.3.3

NEW QUESTION 63
Which LSA type does an OSPF ABR use to advertise external routes generated by an NSSAASBR into the backbone?

Type 5

Type 7

Type 3

Type 1

NEW QUESTION 64
Exhibit

You are asked to assign interface xe-1/0/5 to a virtual switch.
What must be accomplished to complete the configuration?

Interface xe-1/0/5 must be added to routing-instance sw-1 vlan_2.

Interface xe-1/0’5 must be a trunk port.

Interface xe-1/0/5 must be added to routing-instance sw-1.

An IRB interface must be configured to routing-instance sw-1 vlan_2.

NEW QUESTION 65
Exhibit
S Exhibit
LSI1AAS 65501
ISPB AS 65502
Advertised Prefixes: 172.20.0.0/24 172.20.20.0/24 172.20.21.0/24
N
Advertised Prefixes: 172.20.0.0/24
172.20.1.0/24

Referring to the exhibit, which two statements are correct? (Choose two.)

Devices in AS 65512 will prefer ISP A for traffic destined to the 172.20.21.0/24 network.

Devices In AS 65512 will prefer ISP A for traffic destined to the 172.20.0.0/24 network.

Devices in AS 65512 will prefer ISP B for traffic destined to the 172.20.21.0/24 network.

Devices In AS 65512 will prefer ISP B for traffic destined to the 172.20.0.0/24 network.

NEW QUESTION 66
Referring to the exhibit, what does the configuration achieve on the ge-0/0/3 interface?

This interface will assign itself an IPV6 address within this prefix, based on a 64-bit hash of the loopback IPv6 address.

This interface will send a request to a DHCP server, requesting an EUI-64 address in this prefix.

This interface will assign itself an IPv6 address within this prefix, based on its MAC address.

This interface will send a request to an EUI server, requesting a 64-bit interface address within this 64-bit prefix.

NEW QUESTION 67
Click the Exhibit button.

Referring to the exhibit, which statement is true?

The router will attempt to signal the LSP along the IGP shortest path to 192.168.100.1

The router will prune links with insufficient bandwidth from the path before beginning the signaling process

The router will analyze the traffic engineering database to determine the best path through the network

The router will precalculate a valid path through the network for LSP r1-to-r3

NEW QUESTION 68
Click the Exhibit button.

You configured R1 and R2 to form an OSPF adjacency, but the adjacency will not establish.
Referring to the exhibit, which statement correctly identifies the problem?