Verified 350-501 &As – Provide 350-501 with Correct Answers [Q219-Q234]

4/5 - (1 vote)

Verified 350-501 Exam Dumps Q&As – Provide 350-501 with Correct Answers

Pass Your 350-501 Dumps Free Latest Cisco Practice Tests

Target Audience

This Cisco exam is targeted at those individuals who want to validate their improved skills with service provider solutions. It provides the potential candidates with the evaluation of their core knowledge of the domain to grant them the certificate at the end of the certification process. The certificate will prove their skillset that has to include the understanding of service provider infrastructure.

QUESTION 219

Refer to the exhibit Which effect of this configuration is true?

The two routers fail to form a neighbor relationship because they have different IS-IS area types.

The two routers successfully form a neighbor relationship.

The two routers fail to form a neighbor relationship because the authentication configuration is missing.

The two routers fail to form a neighbor relationship because their system IDs are different.

Section: Networking

QUESTION 220
Refer to the exhibit.

An engineer is implementing Auto-RP and reviewing the configuration of the PE-A. Which configuration permits Auto-RP messages to be forwarded over this interface?

PE-A(config-if)#ip pim sparse-mode

PE-A(config-if)#no ip pim bsr-border

PE-A(config-if)#ip igmp version 3

PE-A(config-if)#ip pim sparse-dense-mode

QUESTION 221
Refer to the exhibit:

Which effect of this configuration is true?

it creates a pseudowire class named Cisco

It enables tagging for VLAN 12 on the interface

It enables MPLS on the interface

It enables AToM on interface gigabitethemet1/0

The configuration command xconnect 192.168.0.1 12 encapsulation mpls pw-class cisco is used to set up a pseudowire connection to a remote peer at IP address 192.168.0.1 using MPLS encapsulation. The pw-class cisco refers to a pseudowire class named ‘cisco’ that defines the parameters for the MPLS pseudowire. This configuration is part of setting up Layer 2 VPNs, which are often used in service provider networks to extend services such as Ethernet, ATM, or Frame Relay over an MPLS network.

QUESTION 222
Drag and drop the NAT64 descriptions from the left onto the correct NAT64 types on the right.

Explanation
Stateful (It has 1: N translation, It uses address overloading, It conservers IPv4 addresses) Stateless (It is limited on the number of endpoints, It mandates IPv4-translatable IPv6 address allocation)

QUESTION 223
Drag and Drop Question
Drag and drop the BGP Best Path Algorithm rules from the left into the corresponding order of importance on the right.

QUESTION 224
Refer to the exhibit. The network operations team reported that the access site that is connected to R3 is not connecting to the application server in the data center and that all packets that are sent from the application server to the access site are dropped. The team verified that OSPF and BGP peerings are up in BGP AS 65101 and BGP AS 65201. R4 is expected to receive traffic from the application server route via OSPF. Which action resolves this issue?

Advertise application server 172.16.20.1 in the OSPF routing table on R6

Add the next-hop-self command on R6 to enable R3 iBGP peering

Allow 172.16.20.1 in the BGP advertisement on R3 in the route-map

Remove the route-map on R4 when advertising 172.16.20.1 in BGP to R3

QUESTION 225
Refer to the exhibit:

With which router does IOSXRV-1 have LDP session protection capability enabled but session hold up is not active?

192.168.0.1

192.168.0.3

192.168.0.4

192.168.0.5

QUESTION 226
Refer to the exihibit.

Refer to the exhibit. ISP_A and ISP_B use AS numbers 38321 and 16213 respectively. After a network engineer reloaded router R1, the BGP session with R2 failed to establish. The engineer confirmed BGP next-hop availability with a connectivity test between the router loopback addresses 10.121.123.2 and 10.121.123.1, as well as between interfaces Gi1/1 and Gi1/2. EBGP multihop has been configured on both routers. Which action must the engineer take to resolve the issue?

Configure transport connection-mode passive on R2.

Configure neighbor 172.16.172.1 authentication on R1

Configure neighbor update-source lo0 on R2

Configure remote-as 16213 on R1.

After a router reload, BGP sessions may fail to re-establish due to incorrect source interface configurations for BGP sessions. Since EBGP multihop has been configured, it’s essential that the BGP session uses the correct source interface for establishing the connection. By configuring the neighbor update-source command with the loopback interface on R2, the BGP session will use the stable loopback address rather than the physical interface, which can change state. This ensures that the BGP session remains stable and is not affected by interface states. Reference: BGP Troubleshooting Cheat Sheet With Examples – Catchpoint2, BGP session stuck in Idle state after NSRP failover – Juniper Networks3, BGP Session is Disconnected – Network Playbook

QUESTION 227
Refer to the exhibit. The operations team is implementing a route-map policy. Traffic from source
192.168.30.1 must reach the customer network 192.168.1.1 via the secondary link R4-R6-R5. All other traffic from the data center to the customer network must prefer the primary link R4-R3-R2.
Which action must be taken to meet the requirement for prefix 192.168.1.1/32?

Apply route-map PrefixBlock in on R6 with R5 BGP peering.

Apply route-map PrefixBlock out on R3 with R4 BGP peering.

Apply route-map High-LP on R6 with R4 BGP peering.

Apply route-map Low-LP in on R4 with R3 BGP peering

QUESTION 228
An engineer working for a private service provider with employee id: 3994 37 650 is configuring a Cisco device to redistribute OSPF into BGP. Which task enables the device to filter routes?

Configure a distribute list and associate it to the BGP peer interface

Configure a prefix list and associate it to the BGP peer interface

Configure a route map and reference it with the redistribute command

Configure an access list and reference it with the redistribute command

QUESTION 229
Refer to the exhibit.

Router 1 and router 2 are running IBGP. and router 2 and router 3 are running OSPF Area 0. Router 1 is advertising loopback interlaces Lo0 and Lo2 and router 2 is redistributing BGP into OSPF Area 0. Which configuration must an administrator apply so that router 2 uses a route map to redistribute only the internal route from Lo 2?
A)

B)

C)

Option A

Option B

Option C

Option D

QUESTION 230

Refer to the exhibit. A network engineer configures CPE-1 for QoS with these requirements:
IPv4 and IPv6 traffic originated by the CPE-1 WAN IP address must be marked with DSCP CS3.
IPv4 LAN traffic must be marked with DSCP CS1.
IPv6 LAN traffic must be marked with DSCP default.
Which configuration must the engineer implement on CPE-1?

class-map match-any SELF_TRAFFIC
match access-group name SELF_V4
match access-group name SELF_V6
class-map match-all V4_ TRAFFIC
match protocol ip
class-map match-all V6_TRAFFIC
match protocol ipv6
class-map match-all QG_4
match qos-group 4
class-map match-all QG_6
match qos-group 6
!
policy-map LAN-INPUT
class V4_TRAFFIC
set qos-group 4
class V6_TRAFFIC
set qos-group 6
!
policy-map WAN-OUTPUT
class SELF_TRAFFIC
set ip dscp cs3
class QG_4
set ip dscp cs1
class QG_6
set ip dscp default

class-map match-all SELF_TRAFFIC
match access-group name SELF_V4
match access-group name SELF_V6
class-map match-all V4_ TRAFFIC
match protocol ip
class-map match-all V6_TRAFFIC
match protocol ipv6
class-map match-all QG_4
match qos-group 4
class-map match-all QG_6
match qos-group 6
!
policy-map LAN-INPUT
class V4_TRAFFIC
set qos-group 4
class V6_TRAFFIC
set qos-group 6
!
policy-map WAN-OUTPUT
class SELF_TRAFFIC
set dscp cs3
class QG_4
set ip dscp cs1
class QG_6
set dscp default

class-map match-all SELF_TRAFFIC
match access-group name SELF_V4
match access-group name SELF_V6
class-map match-all V4_ TRAFFIC
match protocol ip
class-map match-all V6_TRAFFIC
match protocol ipv6
class-map match-all QG_4
match qos-group 4
class-map match-all QG_6
match qos-group 6
!
policy-map LAN-INPUT
class V4_TRAFFIC
set qos-group 4
class V6_TRAFFIC
set qos-group 6
!
policy-map WAN-OUTPUT
class SELF_TRAFFIC
set ip dscp cs3
class QG_4
set ip dscp cs1
class QG_6
set ip dscp default

class-map match-any SELF_TRAFFIC
match access-group name SELF_V4
match access-group name SELF_V6
class-map match-all V4_ TRAFFIC
match protocol ip
class-map match-all V6_TRAFFIC
match protocol ipv6
class-map match-all QG_4
match qos-group 4
class-map match-all QG_6
match qos-group 6
!
policy-map LAN-INPUT
class V4_TRAFFIC
set qos-group 4
class V6_TRAFFIC
set qos-group 6
!
policy-map WAN-OUTPUT
class SELF_TRAFFIC
set dscp cs3
class QG_4
set ip dscp cs1
class QG_6
set dscp default

QUESTION 231
Which configuration modifies Local Packet Transport Services hardware policies?
A)

B)

C)

D)

Option A

Option B

Option C

Option D

QUESTION 232
Refer to the exhibit. In which way does router R1 operate differently than router R2?

R1 sends LSA type 2 only, while R2 sends type 1 and type 7 LSAs

R1 sends LSA types 1 and 2, while R2 sends type 1, 2, and 7 LSAs

R1 sends LSA type 2 only and R2 sends LSA type 1 only

R1 sends LSA types 5 and 7, while R2 sends type 1, 2, and 7 LSAs

QUESTION 233
Which type of attack is a protocol attack?

HTTP flood

TFTP flood

SYN flood

Slowloris

QUESTION 234
Which is the benefit of implementing model-driven telemetry in a service provider environment?

It reduces the number of network monitoring tools that are necessary to verify device statistics.

It increases the efficiency of SNMP by pulling system data to requesting servers.

It reduces or eliminates the need to monitor Layer 2 traffic between switches.

It uses reliable transport to push Information to network monitoring tools

Loading …

Cisco 350-501 exam is a 120-minute test that consists of 60-70 questions. 350-501 exam format includes multiple-choice questions, drag-and-drop questions, and simulation-based questions. To pass the exam, candidates need to score at least 825 out of 1000. 350-501 exam fee for the Cisco 350-501 exam is $400, and candidates can take the exam at any Pearson VUE testing center.

Get Top-Rated Cisco 350-501 Exam Dumps Now: https://www.examcost.com/350-501-practice-exam.html