GET Real Fortinet NSE6_FSW-7.2 Exam Questions With 100% Refund Guarantee Feb 15, 2026 [Q26-Q40]

Rate this post

GET Real Fortinet NSE6_FSW-7.2 Exam Questions With 100% Refund Guarantee Feb 15, 2026

Get Special Discount Offer on NSE6_FSW-7.2 Dumps PDF

Fortinet NSE6_FSW-7.2 (Fortinet NSE 6 – FortiSwitch 7.2) exam is a certification test designed to validate the skills of network professionals in configuring, managing, and troubleshooting FortiSwitch devices. NSE6_FSW-7.2 exam is intended for individuals who have experience with Fortinet products and want to demonstrate their expertise in deploying and managing FortiSwitches. Fortinet NSE 6 – FortiSwitch 7.2 certification is highly regarded in the industry and is recognized as a standard for network security professionals.

NO.26 Which statement about using MAC, IP, and protocol-based VLANs on FortiSwitch is true?

lt is a scalable and secure solution in comparison to other Layer 2 security measures.

FortiSwitch uses only the Ethernet type to assign traffic to VLANs.

It provides benefits that can be obtained when using 802.1X authentication.

Endpoints are required to use the same FortiSwitch port to remain members of the VLAN.

NO.27 An administrator needs to deploy managed FortiSwitch devices in a remote location where multiple VLANs must be utilized to segment devices. No Layer 3 switch or router is present. The the only WAN connectivity is the router provided by the ISP connected to the public internet.
Which two items will the administrator need to use? (Choose two.)

A FortiSwitch interface connected to the ISP router configured with fortilink-13-mode enabled.

FortiSwitch and FortiGate devices configured with VXLAN interfaces.

FortiSwitch devices configured with NAT disabled.

FortiSwitch devices that have the required internal hardware for this configuration.

FortiSwitch and FortiGate devices configured with IPsec interfaces.

NO.28 Exhibit.

You need to manage three FortiSwitch devices using a FortiGate device. Two of the FortiSwitch devices initiated a reboot after the authorization process. However, the FortiSwitch device with the configuration shown in the exhibit. did not reboot All three devices completed FortiLink manage-ment authorization successfully.
Why did the FortiSwitch device shown in the exhibit not reboot to complete the authorization pro-cess?
The management mode was set to use FortiLink mode.

Switch auto-discovery is enabled.

The management mode was set to use FortiLink mode.

The FortiSwitch device is scheduled to reboot as part the authorization process

The system time is not in-sync and is using a non-default value

NO.29 Exhibit.

The exhibit shows the current status of the ports on the managed FortiSwitch.
Access-1.
Why would FortiGate display a serial number in the Native VLAN column associated with the port23 entry?

Port23 is a member of a trunk that uses the Access-1 FortiSwitch senal number as the name of the trunk.

Port23 is configured as the dedicated management interface.

A standalone switch with the showm serial number is connected on por123.

Ports connect to adjacent FortiSwitch devices will show their.serial number as the na-tive VLAN

NO.30 Which feature should you enable to reduce the number or unwanted IGMP reports processed by the IGMP querier?

Enable the IGMP flood setting on the static port for all multicast groups.

Enable the IGMP flood reports setting on the mRouter port.

Enable IGMP snooping proxy.

Enable IGMP flood unknown multicast traffic on the global setting.

NO.31 Refer to the diagnostic output:

Two entries in the exhibit show that the same MAC address has been used in two different VLANs. Which MAC address is shown in the above output?

It is a MAC address of FortiLink interface on FortiGate.

It is a MAC address of a switch that accepts multiple VLANs.

It is a MAC address of an upstream FortiSwitch.

It is a MAC address of FortiGate in HA configuration.

NO.32 Exhibit.

Two routes are not installed in the forwarding information base (FIB) as shown in the exnibit. Which two statements about these two route entries are true? (Choose two.)

These two routes have a higher administrative distance value available to the destination networks.

These two routes will become primary, if the best routes are removed.

These two routes will be used as load-balancing routes.

These two routes are available in the hardware routing table.

NO.33 Which two statements about VLAN assignments on FortiSwitch ports are true? (Choose two.)

Configure a native VLAN on the FortiLink

Assign an IP address and subnet mask to FortiSwitch VLANs

Only assign one native VLAN on a port

Assign untagged VLANs using FortiGate CLI

NO.34 Refer to the exhibit.

What two conclusions can be made regarding DHCP snooping configuration? (Choose two.)

Maximum value to accept clients DHCP request is configured as per DHCP server range.

FortiSwitch is configured to trust DHCP replies coming on FortiLink interface.

DHCP clients that are trusted by DHCP snooping configured is only one.

Global configuration for DHCP snooping is set to forward DHCP client requests on all ports in the VLAN.

NO.35 Refer to the exhibit.

The exhibit shows the current status of the ports on the managed FortiSwitch. Access-1.
Why would FortiGate display a serial number in the Native VLAN column associated with the port23 entry?

port23 is configured as the dedicated management interface.

Ports connected to adjacent FortiSwitch devices show their serial number as the native VLAN.

port23 is a member of a trunk that uses the Access-1 FortiSwitch serial number as the name of the trunk.

A standalone switch with the shown serial number is connected on port23.

NO.36 Refer to the configuration:

Which two conditions does FortiSwitch need to meet to successfully configure the options shown in the exhibit above? (Choose two.)

The FortiSwitch model is equipped with a maximum of 54 interfaces

FortiSwitch would need to be rebooted.

The split port can be assigned to a native VLAN.

The Dort full speed prior to the split was 100G QSFP+.

NO.37 Which statement about the IGMP snooping querier when enabled on a VLAN is true?

Active multicast receiver entries are aging on each IGMP query sent on the VLAN

IGMP reports on the VLAN are forwarded to all switch ports.

The setting can only be enabled using the FortiSwitch CLI.

All other indirectly connected switches will be unable to get IGMP multicast traffic.

NO.38 What feature can network administrators use to segment network operations and the administration of managed FortiSwitch devices on FortiGate?

FortiGate multi-tenancy

Multi-chassis link aggregation trunk

FortiGate clustering protocol

FortiLink split interface

NO.39 Which two rules used by MSTP are similar to rules used by other STP methods? (Choose two.)

MSTP uses port role election, similar to rapid STP on the instances.

MSTP uses alternate path and primary path, similar to regular STP.

MSTP uses root bridge selection, similar to rapid STP

MSTP uses timers for transitioning the ports, similar to regular STP.

NO.40 Which is a requirement to enable SNMP v2c on a managed FortiSwitch?

Create an SNMP user to use for authentication and encryption.

Specify an SNMP host to send traps to.

Enable an SNMP v3 to handle traps messages with SNMP hosts.

Configure SNMP agent and communities.

Fortinet NSE6_FSW-7.2 certification exam is ideal for network administrators who want to demonstrate their expertise in managing FortiSwitches. Fortinet NSE 6 – FortiSwitch 7.2 certification also validates the skills of security professionals who want to enhance their knowledge of network security. NSE6_FSW-7.2 exam is designed to test the candidate’s ability to configure and manage FortiSwitches and ensure that the network is secure and reliable.

PDF Download Fortinet Test To Gain Brilliante Result!: https://www.examcost.com/NSE6_FSW-7.2-practice-exam.html